MUSELOCK Walkthru!

[d@n.]

Here the MUSElock Walkthru
by gamesuy

Walkthrough:

1. Get the paper.
2. Check Garbage can for the can.
3. Go to the armchair and look at the left arm. There should be a very hard to see, but visible outline of a rectangle. Click the rectangle to open it and then grab the box.
4. Go to a spot where you can see the doormat and click on it to go to it. click it again to lift it and take the key.
5. Use the key by clicking it and then click on the keyhole. It should say door is unlocked. click the handle to open the door.
6. Go to the projector screen and click that panel (with the up and down arrows) that lets it go up and down. Make the screen go up and then click the rectangular outline next to the arrow keys. It will reveal a fuse. take it and then go back to where you could face the screen.
7. The control panel (the bottom rectangle coverd with glass) should be seen. click it to go to it and then select your paper. click the control panel, there should be a very faint brown half circle towards the center) to make a little funnel. Then click your orange juice and click the paper funnel. It will short circuit the fuse. The room will turn red
8. You should see a square with black dots on the panel. click the top right dot, the bottom left dot, middle dot, bottom right and then top left. then click the button with a lock on it. that will open up the glass over the short-out fuse.
9. Grab the short-out fuse (right panel) and select your box that you took from the chair. look at it in greater detail with the inspect item button. select your short-out fuse and then click the hole in the box. then take the key in the box.
10. Go under the desk and use the black key on the bomb. remove the cover and click a piece of the big white blob (C4) and then click the clip connected to the C4. then you can remove it.
11. take the projector cover from the square projector on the wall. The projector cover will have a red circle in the middle.
12. go to the glass diamond and place the C4 white blob piece that you took from the bomb and place it on the glass. go to the projector facing the glass diamond and place the projector cover on it. Go to the projector screen and place the fuse in the LEFT panel. then go to the floor projector and click the button that looks like a sun. The glass will explode and then the blue bulb can be taken. Grab it.
13. Go back to projector screen and take the fuse out (this is VERY IMPORTANT) grab the bulb and place it into the lamp on the desk.
14. go under the desk and place the big metal (gold) key where the bomb use to be.
15. go to the fuse box (spot-where you took the short out fuse) and place the working one into the slot on the left. go to the lamp and click the button on the base. the room will turn blue and then turn around to look at the paintings. Note that the paintings show symbols.
16. take the fuse out of the fuse slot and place it back into the up and down keyboard slot. click down and bring the projector screen down. take the projector cover from the projector and place it back to the one on the wall. press the sun on the wall projector and find the corresponding symbol. (if you got the pink square with a circle in the middle, that is number 8. If you got the pink square then it is number 4.) (Writing down the symbols on from the projector makes it easier.)
17. Make the projector screen rise and then go to the keypad. punch in your code. If the light turns green, then voila your free. You can exit through the door.

[MOYA]

Nice walk through d@n.

[sassy1_ntn]

Ok, I've gotten all the way to the end where you put in your code on the keypad and it didnt work. Went to look at the walkthru for help. But, that didnt help either. I keep getting a weird symbol on the projector screen that doesnt match what's on the pictures. And when I try to put in different #'s on the keypad, the panel comes down.....Any suggestions or hints????

[d@n.]

Originally Posted by MOYA

Nice walk through d@n.

Thanks Moya

[d@n.]

Originally Posted by sassy1_ntn

Ok, I've gotten all the way to the end where you put in your code on the keypad and it didnt work. Went to look at the walkthru for help. But, that didnt help either. I keep getting a weird symbol on the projector screen that doesnt match what's on the pictures. And when I try to put in different #'s on the keypad, the panel comes down.....Any suggestions or hints????

alrite let me try out n let u know